All are edge banded to keep smooth edges. We finish it off with a polyurethane clear coat to protect the wood stain. Our wood bed rails are made from a 7/8 inch plywood core with a veneer finish. The wood slat bearer will accommodate either wood or metal slats. Wooden bed rails are made of high quality wood and come in three standard finishes and unfinished. If you require a perfect match, order the unfinished bed rails, and work with your paint store to select the right stain. Please note that wooden bed rails come in a dark, medium, and light finish and unfinished. They are 76 inches long and replace metal rails or wooden rails that have warped, been lost, or damaged over time. Pay attention to where you drive the screws on this DIY twin floor bed with rails so they won’t cross.“Carl, thanks for the quick response, bed rails arrived today as promised and the bed had been assembled with new queen mattress and box spring!” – John U. This part is very straightforward - use 2 ½” screws to attach all the sides. Until the assembly of all the sides, I could use a garage, but it would be best to put it all together inside. Sand all the sides again with 220 grit paper. Luckily, my client didn’t mind and I could leave it this way. Sadly, it was too late to fix it, unless I’d start over again. I realized it was the wrong side only after I already attached the rails. Originally I had planned to make the entrance on the left side but I made a mistake. When assembling the front side pay attention to what side the entrance will be on. Take another 2x4x76" and attach rails to it following exact same steps as before. Use 2 ½" screw on the top of the rails Step 4. It’s slightly different from the sides.Īttach 2x2x76" On the top using 2 ½” screws and countersink bit. If you are following my plan, pay special attention to the distance between the rails. Use a plywood sheet or an even floor to assemble the rails To assemble the side it was easier for me to keep it on the plywood sheet since I didn’t have enough space on my workbench. Take 2x4x76" and following the same steps as making side rails, attach rails to it. Ready side of the bed Make two identical sides Step 3. Also, use a countersink bit so the screws are flush. It's worth mentioning that I used a countersink bit so the screws are flush with the board.Īttach 2x2x39" on the top of the rails. I used 2 ½" screws for that and simply drove them through the sides. Use wood glue and 2 ½" pocket hole screws to attach rails to the bottom.Īdd two 2x2x24" boards on the ends of the sides. Make a block to have exact spacing between the rails. As an alternative, you could use 4" screws and drive them through the 2x4"s. I used a Kreg jig to make pocket holes on the bottom, since it will be covered with the mattress they won't be visible. I used Kreg jig to attach rails to the bottom When all wood was prepped and ready, I made two identical sides. Make a stop block for the miter saw to make it easier to cut the rails As a result, you'll get perfectly cut boards. To make sure that they all are exactly the same length, create this simple stop block on your miter saw. You'd need to make a lot of the same cuts for this project (like rails, for example). Always make your way up in numbers to archive the smoothest finish possible. Sand it thoroughly using 80,120 and 220 grit sandpaper. Cut and prepare the woodĬut the wood according to a plan. Speakeasy library room reveal + budget breakdown So what will we need to make a DIY twin floor bed with rails? Since we needed 10 of them, it added up being more expensive than I anticipated. The crispy squares edges of the boards saved me so much time and made it look super nice but they are pricey. I went the easier route and purchased 2x2"x8' in select pine. It would take you longer to prepare and sand it and you probably would have to cut off the edges too, unless you like the rounded edges. If you want to make this project cheaper, then get 2x2"s from construction lumber. This way furniture will look more professional. Set the table saw on ⅛" less than the board and cut it off. When making furniture I like to cut off the edges of construction lumber and square them. When I was done, the assembly didn't take long. As I mentioned before, preparing the wood took the longest time of this project.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |